#Fldigi and cw operation how to#
#Fldigi and cw operation install#
#Fldigi and cw operation manual#
#Fldigi and cw operation download#

#Fldigi and cw operation manual#

The fldigi manual describes a simple circuit that allows the sound card to hard-key the CW input of your transmitter. If you want to operate CW from fldigi, there is a simpler way to do so that is almost certainly guaranteed to be cleaner for most newer radios. To emit a clean signal, one does need to be careful not to overdrive the transmitter audio stages, avoid compressors, etc. In fact, this method has some advantages if done properly, because the modulating wave shape can be very precisely controlled to minimize key clicks, etc. Watch for my videos.Is quite correct - there is certainly nothing wrong with using a tone to modulate an SSB transmitter to produce CW. I will cover more on operating Fldigi in the future. There is a lot you can do with Fldigi, so much so, it would be too time consuming to go through all of it. xml for the Icom 7610 (Download and use at your own risk). xml file for your radio and place it in the “Rigs” folder of your Fldigi installation.

#Fldigi and cw operation download#

Whatever radio you are using, download the appropiate. I typically run mine at 1/4 of the ALC scale on the Icom 73. RTTY AFSK is like PSK31, you will need to be mindful of the ALC level. You can do most things with just the USB cable, but the CI-V cable comes in very handy and is inexpensive.Ī note about Easy RTTY (AFSK): By using RTTY AFSK you do not need an extra port for FSK keying, thus making it easier to operate Fldigi RTTY AFSK when you are using a radio like the Icom 7300. So on the Icom 7300 I typically have connected a USB cable and also the CI-V cable.

This cable plugs into a USB port on your computer and the other end goes into the “Remote” jack on the back of the radio. When finished setting it up you will have the basics for getting started.Ī note about RigCAT: I am using my COM 12 which is the CI-V cable. When finished with the initial setup, visit the sections (photos above) and enter them into your installation. The first time you open it you will be guided to add information, some of which is shown in the photos above.

#Fldigi and cw operation install#

Install it as you would any Windows program (other OS available). If you haven’t installed Fldigi, the download is here. Configure yours as seen in the photos above. If you have Fldigi installed and you are using it, this will be easy. Then click your back button to return here. Fldigi Setup Easy RTTY (AFSK) PSK31 & CWĬlick near the top of the image to enlarge. In Configuration, go to Fldigi under Applications and uncheck the box to start Fldigi on startup. NOTE: There is no need to start the Fldigi service in Log4OM. Go to Program Configuration and then ADIF Functions You can also see how I did JS8Call in my other video here, starting at 1:04. If you have been following along or have Log4OM installed, add a line in the ADIF Functions tab. Those will give you what you need to catch up and configure Fldigi as shown in this post.WSJT-X and LOG4OM Tutorial Free and Easy!,.NEW Log4OM 2 Logging Program Install and Initial Setup,.If you are new to Log4OM please see my previous posts: Here are the screen capture links for the Icom 7300 and Icom 7610 internal settings.

#Fldigi and cw operation how to#

If you have been using FT8, JS8Call or PSK31 you’ll know how to setup your radio. The internal settings of your radio need to be setup for digital mode operation. The Icom 7300 I have in my camper worked FB while traveling and this post will cover setting up it, the Icom 7610 and just about any other radio. The Icom 7610 Fldigi, Log4OM, WSJT-X, GT and now add Fldigi to the mix for Easy RTTY (AFSK), PSK31 and CW. I had a wonderful time in Arizona and New Mexico, but it’s good to be back home and using the Icom 7610.